Make Your Own Ceramic Mosaic Table Top

How to make a mosaic table top for outdoors or indoors!

mosaic table top

DIY mosaic table tops are a wonderful way to dress up furniture with a handmade touch. You can even use broken pieces of pottery for a mosaic as long as it’s relatively flat. In today’s post, we’ve gathered two great resources for those interested in making a ceramic mosaic table top. First, in an excerpt from her popular video Creative Tile Making, Angelica Pozo shares her technique for making a cut tile mosaic table top. 

Then, Clay Cunningham explains how he made a mosaic table top out of an old broken patio table. He takes you from the planning stages to the final grouting and shares his clay body and clear glaze recipe. – Jennifer Poellot Harnetty, editor.


How to Design, Make, and Install Ceramic Tiles and Murals

Designing ceramic tiles and murals has never been easier when you download this freebieHow to Design, Make, and Install Ceramic Tiles and Murals.



This clip was excerpted from Creative Tile Making, which is available in the Ceramic Arts Network Shop.


mosaic table topHow to Make a Mosaic Table Top From a Broken Table

by Clay Cunningham

I recently returned from a vacation to discover that a spring storm had destroyed the glass top of my patio table. I was faced with two options—order a new manufactured tabletop or put my talents to work by designing and building a new one out of clay. With my summer schedule open, my wife and I started our mosaic table top. This is a great project for use in any outdoor setting, but could also be used indoors.

Creating the Mosaic Table Top Design

Begin by purchasing a 5/8-inch thick sheet of exterior plywood. Cut the plywood to the shape of the table frame with a hand-held jigsaw. You can also use a hole saw to cut a hole in the middle for an umbrella to fit through. Once the plywood is ready, start designing your DIY mosaic table top.

How to Design, Make, and Install Ceramic Tiles and Murals

Designing ceramic tiles and murals has never been easier when you download this freebieHow to Design, Make, and Install Ceramic Tiles and Murals.



Lay the plywood on the floor, cover it with large sheets of drawing paper (24 × 36) and lightly tape them together to hold their position. Cut the paper to the shape of the tabletop and sketch a design in pencil (figure 1). We decided on an image of aspen trees with beautiful red and yellow fall leaves, but any image is possible with this technique. There are a few considerations when designing a mosaic. First, large clay tiles tend to warp (see this post for tips on making flat tile), which leads to an uneven top, so keep individual pieces small—less than eight inches on a tile’s longest dimension. Second, the tiles fit together like a puzzle, but an excess of undulations causes trouble. It’s best not to have pieces lock into one another. Finally, including a border will not only visually ‘frame’ your design, but also ensure a nice, even edge to the entire table.

Finalize the image in pen and remove the tape carefully. Number the individual sheets to help keep track of their position. Also indicate the four quadrants of the plywood sheet as well.

mosaic table top


Make your own ceramic tiles!
Check out 
Creative Tile Making with Angelica Pozo in the Ceramic Arts Shop.


Supplies:

  • Drawing Paper
  • Plywood Table Top
  • Respirator
  • Jiffy Mixer
  • Grout
  • Tile Adhesive
  • Trowel
  • Scraper
  • Buckets
  • Wet sponge
  • Gloves
  • Needle Tool and Stiff Flexible Rib

Making Mosaic Tiles

Roll out a large ¼-inch thick slab of clay (we used white earthenware). This will be thick enough for strength yet not so thick that it makes the table top excessively heavy. Now lay one quadrant of the paper out onto the clay and cut the edges to match the drawing. To ‘trace’ the image onto the clay, use a needle tool to do what I call the dot-to-dot technique (also, check out this image transfer technique in the archives!). Simply follow along the drawing, lightly piercing through the paper with the needle tool until the entire drawing is perforated (figure 2). It’s important not to press down on the needle tool too hard. If you do, you’ll stab into the clay, which distorts the drawing and makes for rough, gouged edges. Remove the paper to reveal the dot-to-dot drawing on the clay. Continue this same technique with the other three quadrants.

Allow the clay to dry to an early leather-hard state then cut along the dotted lines with a fettling knife (figure 3). Check the cut pieces with the original paper design for overall consistency. After drying a bit more, smooth the tiles out along the edges and round off any sharp points. If the edges and points are not smoothed, they may turn into sharp areas poking out on your tabletop.

mosaic table top

To prevent warping in the tiles, carefully flip and gently compressed each one numerous times over the course of a few days or dry them on an open wire rack. While the tiles are upside down, incise small grooves into the back of the tiles with an old pen. This groove allows the tile glue to grip and hold onto the tile. Do not use a needle tool to create the grooves as it will make a line that is too thin to allow the glue to fill the groove. When flipping the tiles, keep the them close together and in their correct position.

Glazing and Firing Mosaic Tiles

Meticulous note taking is important when moving the tiles to the kiln shelf. Make detailed drawings of which clay quadrants are on which shelves and where the shelves are placed in the kiln. Without these notes, it’s easy to get confused. Space the tiles out a bit to allow enough room to add underglaze to them without accidentally getting the wrong color on a tile. Though you could add the underglaze to the tiles before placing them on the kiln shelf, placing them first avoids over handling of the underglazed pieces. With a wide hakeme brush, apply underglazes in a thick, opaque coat onto the tiles (figure 4). After the underglaze is completely dry, apply a thin coat of a clear glaze and load them into the kiln. You can bisque fire the tiles before glazing them if you wish, but I wanted to eliminate as many unnecessary steps as possible. Fire them slowly to the appropriate cone.

Prepping and Setting the Mosaic Table Top

Brush three coats of weatherproofing water sealant onto the plywood tabletop to ensure its longevity. Gather the tile glue, grout, and trowels for creating your mosaic. All of these supplies came to less than $50 (including the plywood) and can be purchased at your local home center.

Now it’s time to construct your mosaic. Begin by laying the tiles out onto the plywood, allowing an even amount of space between each tile. Because the clay has a shrinkage rate of around 10%, the mosaic will perfectly fit your tabletop and allow just enough room between the tiles for the grout. Once the tiles are situated, they’re ready to be glued down. Flip each tile over, coat with a liberal dollop of tile glue (figure 5), and immediately place into position, paying careful attention to retain an equal amount of space between all of the tiles. Continue this process until every tile is glued and placed. I recommend going back over each tile and giving it a little wiggle to ensure that none are missed. Trust me, you’ll find one.

Allow the glue to dry overnight and add the grout the next morning. The grout does two things—first, it adds a stained-glass effect with all of the tiles separated by a single, unifying color and second, it keeps water and other materials from getting between the tiles and rotting the wood underneath. Note: If any water freezes between the tiles, it will expand and break the mosaic.

Grout comes in an unending variety of colors so choose the best color for your design. A black grout helps colorful tiles ‘pop’ out at the viewer (see this example of creative use of ceramic tile grout!). Mix the grout per the instructions on the package to a smooth, thick concrete consistency and immediately trowel directly onto the mosaic. It’s important to get the grout down into every nook and cranny between the tiles (figure 6). With one motion, press the grout down into the empty spaces. With the next motion, scrape it off of the top surface. Continue until the entire tabletop is coated with grout, including the edge of the table where the tile and plywood meet.

mosaic table top

Though the mosaic table top will look like a mess at this point, cleaning it off is a snap. As the grout begins to dull in color, use a soft rubber rib to scrape it away from the top (figure 7). The scraping removes all but a fine film on top of the tiles which can be easily wiped away. Remember, it’s always important to wear a respirator or dust mask whenever handing dry materials. Last, a light sponging with a thoroughly rung out damp sponge brightens all of the colors and a dry towel removes any remaining film. The entire grouting process can be completed in less than an hour.

The only thing left to do is secure the mosaic table top to the table frame. Cut out small blocks of wood and insert wood screws into them. These serve as the brackets that lock the tabletop into place, yet allow it to be removed if needed. From under the table, place each bracket a few millimeters away from the table frame, one in each quadrant, and screw them into the underside of the table top. And with that, the mosaic table top is complete.


mosaic table top

The completed mosaic ready to be placed onto the table frame.

Clay’s White Earthenware Cone 04
Talc 50
Custer Feldspar 25
OM4 Ball Clay 25
Total: 100%
Carly’s Clear Glaze Cone 04
Pemco 626 Frit 25
Gerstley Borate 35
Spodumene 20
EPK Kaolin 20
Total 100%

 Add: Handful of Epsom Salt


Clay Cunningham is a ceramic artist and instructor, currently teaching at Lewis Central High School in Council Bluffs, Iowa. To see more of his work, or for contact information, visit www.claycunningham.org 

**First published in 2013
Comments
  • Great article my table broke and I’m looking to do somthing similar! My husband and I just created a blog about tiles

  • Marie H B.

    Not sure how you are finishing the edges- if the table top originally had a metal rim, then the tiles and their border can be fit within- otherwise you have the plywood visible from the side, under the edging tiles. Beautiful design by the way!

  • Judy J.

    Tilework that is going outside, exposed to the elements, should not be on plywood, but on a concrete-based board used in bathrooms etc. Also, doing the transfer drawing on a thin sheet of plastic makes it easier to transfer to the tiles. Create your design on the paper, and number each piece. Then cover it with plastic and trace it in magic marker. Lay the plastic with the drawing on top of the clay, and with a pencil, knitting needle or other pointed tool trace over all the lines. When you remove the plastic the lines will all be engraved in the clay, ready to cut. I dry my tiles between layers of sheetrock, and no warping occurs. I lay the clay slab directly on the sheetrock before cutting, to handle it as little as possible, and place another piece of sheetrock on top of the cut tiles. That way they do not need to be flipped, and only handled once when they are leather hard to smooth the edges and groove the backs.(And do any carving or other decoration.) At this time I also number each piece to correspond with the original drawing. If you have a large project such as this table, it is easy to cut the design into smaller parts by simply cutting the plastic or drawing a line with another color where the design break occurs. Once everything is fired it is easy to reassemble the pieces by following the numbers on the back, no matter how complex the work is.

  • John S.

    If you need to put the table away (storage) for the winter, I would suggest either a bracket or holes in the plywood backing to allow you to hang it in the garage and enjoy it all year long.

  • Subscriber T.

    Once the entire piece is grouted and the grout is dry, I would suggest using a grout sealer. This can also be purchased at your local hardware store. It will keep water from seeping into the grout, and cracking the grout if it freezes. Great article!

Leave a Reply

You must be logged in to post a comment.

Enter Your Log In Credentials
This setting should only be used on your home or work computer.

Larger version of the image

Send this to a friend